How to replace the wheel bearing assembly - Focus on professional bearings and components manufacturing and supplying

NEWSLocation: Home > NEWS

How to replace the wheel bearing assembly

Instructions

1 Park the vehicle on a flat, level paved or concrete surface. Place the vehicle in gear or

park and apply the parking brake.

2 Place a wheel chock behind a rear tire (or front if you're doing a rear hub-bearing assembly).

3 Loosen the lug nuts on the wheel of the hub bearing you're replacing with the breaking

bar and a socket; do not remove them.

4 Lift the wheel with the floor jack in a safe and secure manner. Support the vehicle on a

jack stand, preferably on the frame rail if present.

5 Remove the lug nuts and wheel.

6 Locate the caliper bolts and remove them with the ratchet and a socket.

7 Pry the caliper off gently using a large straight-edged screwdriver and support the caliper

on the coil spring with a bungee cord. Do not allow the caliper to dangle on the rubber

brake hose.

8 Locate the caliper bridge bolts (if applicable) and remove them with the ratchet and a

socket. You may want to break them loose with the breaking bar first if they're really tight.

On some vehicles, the brake pads will remain in the bridge and can be removed by prying

out with the screwdriver. On other models, the pads stay intact and may be clipped to the

caliper. If you have to remove the pads, do so by taking note how they were placed in the

bridge and be sure you're able to put them back in the same manner they were extracted.

9 Remove the rotor. If it is stuck to the hub, you may have to hit it with a large rubber mallet.

Use a rubber mallet if you're not going to replace the rotor, so you don't damage the surface.

10 Remove any ABS wires attached to the hub bearing assembly (if applicable) or unclip the

wire and trace it to the plug. In many applications, if the ABS wire is integrated with the wheel- bearing hub assembly, a new one will come with it. If you're not sure, check the box of the

new bearing and if there's an ABS wire, follow the wire until you locate the plug, unplug it and

unclip it from its mounts. If ABS is present but not integrated with the bearing assembly,

remove the sensor from the bearing with a ratchet and socket.

11 Remove the spindle nut with the breaking bar and a spindle nut socket. Remove the washer

behind the spindle nut.

12 Locate the wheel-bearing assembly bolts behind the knuckle, and loosen them with the

breaking bar and socket. The location of these can sometimes create a tight area to place

a socket and tool on to remove them with. You may have to apply some ingenuity.

Replace the socket on the ratchet to extract the bolts quickly and easier. Most hubs have

three or four bolts.

13 Install the slide hammer onto the lug studs and secure with tightened lug nuts. This may

take several attempts and a couple of breaks in between to remove the hub bearing from

the knuckle. Pay close attention to your progress and try to determine when the bearing

will separate. Take note of how the backing plate is installed between the knuckle and the

bearing so you can replace it in the same manner.

14 Sand off the rust and corrosion around the knuckle with a fine- to medium-grade

sandpaper. Move the drive-shaft spindle around to get it out of your way. Take your time

when doing this and make sure it's as clean as possible.

15 Place the backing plate in its original position and place the new bearing onto the knuckle.

Manipulate the drive-shaft spindle splines into the center of the hub bearing. Push the bearing on as far as you can, making sure to line it up correctly if ABS lines or plugs are present.

16 Replace the wheel-bearing assembly bolts. They're pretty long, so as soon as you can

thread them into the new bearing, start to tighten them. Pull the bearing in by tightening the bolts a little bit at a time and then switching to the next bolt to make sure the bearing assembly

does not shift in the knuckle and cause damage. Once the bearing is drawn in flush, use the

breaking bar to get the bolts as tight as you can get them.

17 Replace washer and spindle nut and tighten to proper torque specifications with the half- inch

drive torque wrench and spindle socket.

18 Replace the brakes in the same manner you extracted them. You may need to push the

caliper piston in a bit with a C-clamp to get it over the rotor. Plug in the ABS lines or reattach

them to the bearing, if applicable.

19 Replace the tire and lug nuts, and tighten the lug nuts as tight as you can get them.

20 Lower the ehicle and tighten the lug nuts in an alternate fashion with the torque wrench

and socket at the correct wheel nut specifications torque setting.

21 Pump the brake pedal if you had to push the caliper piston in with a C-clamp to restore

hydraulic pressure to that caliper piston.

22 Remove the wheel chock, release the parking brake, and go for a test drive.

Tips & Warnings

•Learn as much as you can about your vehicle and wheel-bearing assembly before starting

the project. Refer to the owner's manual to obtain the proper torque specifications where applicable. If you do not have an owners manual, ask the parts store where you're buying

the wheel bearing to look them up for you.

•Some applications require a special 12-point socket to extract the wheel-bearing assembly bolts.

•Allow time to perform this repair. It's going to take a few hours the first time.

WOW bearing design and manufacture near 1000 models wheel bearings, the second and third generation wheel hub units, covering of all kinds of cars, heavy trucks and various kinds of vehicles. We could manufacture new models according to the customer’s drawings and samples.

Please send your inquiry to our email: sales@wow-bearings.com or wowbearings@china.com